|Product description :|
|This product is headquartered in the U.S. domestic production Oster
Group, a new dust seal concrete curing materials, including
selected high activity fluorosilicone material, is environmentally
friendly colorless transparent liquid (odorless, colorless,
non-toxic, non-combustible), Hardening of the material selected,
can penetrate the surface 3-5mm, curing of concrete ingredients to
make a strong entity, to make concrete permanently hardening,
strengthening and sealing.|
Products for the three components
Lawson OS-1 concrete sealed curing agent
Lawson OS-2 Concrete curing agent sealed
Lawson OS-3 high-gloss anti-slip sealed curing agent
|1, the product used for curing the new and old concrete surface,
making it dust-proof, resistant to wear and suppression of certain
chemical substances Royal erosion, improve durability and wear
resistance of the concrete surface|
2, applies to all industrial plants and warehouses, cargo loading
and unloading areas, parking lots
3, for emery abrasion floor hardening and maintenance.
4, especially for treatment from the sand floor.
|1, compared with other liquid curing agent, more responsive, more
secure, increase strength faster, higher, wider scope.|
2, can significantly improve the wear resistance of concrete
3, chemical reactions can be cleared through the concrete surface
4, curing from the sand surface and grass-roots epoxy coating to
increase adhesion. Thereby increasing the durability of epoxy
5, the construction time is short, simple, without interrupting
6, the cost of economic, cost-effective.
7, in particular, the problem can be used as the increase in
wear-resistant floor surface repair agents and agents to improve
the wear-resistant floor surface strength.
8, can also be used as a wear-resistant floor of the curing agent
and sealing agent.
9, the product from the sand on the floor curing serious as the
best product, can not afford to permanently ensure the sand floor
and low cost.
|1, dust and curing|
Lower strength of concrete surfaces and the inherent quality
defects, often prone to wear and tear due to traffic from the dust,
which will not only generate a lot of dust on forklift safety and
can also cause great harm, is the industry's problems of ordinary
floor < br /> Aust: Lawson two-step curing agent to remove
concrete dust, thereby improving the durability of concrete. First,
the product can penetrate the surface layer the following 3-5mm;
Second, the product of the hardened concrete in the displacement
components and loose material chemical reaction to produce hard
insoluble. This chemical reaction can make a few millimeters deep,
thick layer of concrete curing seal.
This product can remove the loose material in concrete to increase
the density of the surface and improve the concrete strength and
abrasion resistance, compressive strength and wear resistance can
be increased by 50% or more.
3, sealing penetration
This product is insoluble solid reaction of the concrete block can
be filled capillary has to produce a dense non-porous surface
layer, can improve the impermeability of concrete up to 35% or
This product can be sealed concrete and congestion, reduce pores
and reduce the evaporation of water in concrete to strengthen the
concrete curing, inhibition of turtle cracks.
5, the life
The surface layer of hardened concrete product directly to form a
hardened layer (not the additional coating) than the other curing
agent, the pigment of the hardened layer "while" more integrated,
permanently. Permanently extend the life of the ground.
|1, the preparatory work|
Structure of the surface must be treated well, no pollutants, dust
and other coatings, cracks and holes must be repaired.
2, the construction
Crying with a low-pressure spray or roller, soft brush evenly
brushing. Depending on the extent and permeability of compacted
base surface brushing OS-1 components and OS-2 group were the two
to three. Cleaning the surface to remove excess material, or drying
grain will leave a white bar. As needed, brushing OS-3 components
Dosage of 3-4 square / kg, depending on the actual site of
absorption rate data may be