16×2200 Metal Sheet Slitting Machine Line Steel Coil Cut To Length
Hydraulic entry coil car
Hydraulic cantilever de-coiler
4-h pre-leveling machine
Side guide device
Servo precision straightening machine
1400 hydraulic cutter
Hydraulic lifting table
Pneumatic stacker device
1. Hydraulic entry coil car
The car can move levelly and vertically, which is convenient for
putting the steel coils into the de-coiler.
It is driven vertically by hydraulic cylinder with four guide
The level movement is driven by cycloid motor.
The capacity it can carry is 10 Tons(Max).
2. Hydraulic cantilever de-coiler
Supporting the coils and doing uncoiling. The capacity is
It adopts the hydraulic oil cylinder to make the decoiler
expandable and fit to the inner diameter of coils. It is equipped
with the cantilever.
40N.m moment motor drive the coils running and can do forward and
reverse running as well as do the decoiling with tension.
The core can ensure the expand range φ508 of the coils inner
Structure: welding by the steel plates and profiled bar.
3. 4-h pre-leveling machine
It is equipped with the press and pinch device at the entry which
is driven by hydraulic.
It is composed of 17 leveling rollers, 2 groups of supporting
rollers ,driving device and 2 pinch rollers and frame. Both sides
of each rolling wheel is transmitted by needle pins all are the
main force rollers. the total quantity of the rollers is 15, the
diameter is 65and the distance between the rollers is 70mm, with
supporting rollers. All the rollers are plating leather to protect
the stainless steel plate surface is not wear.
The function of the supporting roller is to balance the leveling
rollers force and reduce the friction to the rollers.
Driving model: all the independent rollers and gear box are driven
by 30Kw frequency control motor
4. Side guide device
It uses the vertical roller-wheel on the both sides to direct
strips into straightening device and cutting machine.
The stand rollers on both sides are adjusted by leadscrew. The
range of the width is 500-1400mm.
5. Servo precision straightening machine
It is controlled by servo electromotor and used to regulate for
high speed feed and precise length control.
The operation is done at the control table with programmable
Drive model:15Kw servo motor with precise decelerating transmission
and synchronous to transport the belt to feed rollers
6. 1400 Hydraulic cutter
Shear model: cut from up to down hydraulically which is cooperate
with the signal direct from the feeder and shear automatically
Adopt gap adjusting design to cut the materials and can shear 3mm
steel plate safely after heat treatment
7. Transportation table
Transportation belt is skidproof and wearable
Drive: cooperate with the line speed and is transmitted by 2.2KW
frequency control motor
8. Hydraulic lifting table
The length of plates can be 6m
The width cab be ranged from 500 to 1400mm.
9. Pneumatic stacker device
The plates are piled pneumatically and PLC controls the lifting.
Three 0.75kw motors drag to adjust the width and the length.
It is equipped with the wind device which cooperate with the high
pressure fan to prevent the sheets from friction.
10. Pneumatic system
The pneumatic system is composed of the air power(prepared by the
buyer), air source treatment components , salennoid, relevant
pipeline and air cylinder, etc. The components such as salennoids
are adopted high quality products.
Technical parameters: stress of air source: 0.4-0.6Mpa. The
11. Hydraulic system
Ensure the using of every hydraulic part.
The working pressure of the hydraulic system is 6.3-16Mpa.
12. Electrical system
Adopt the servo control mode and PLC control mode,It is controlled
by LCD screen with fixed-length cutting by codes and count
Main technical parameter
|Type||Thickness Range||Width Range||Cutting Length||Cutting Precision||Roller Numbers||Roller Diameter|